Water-based Acrylic Sealer & Dust Proofer with 14% Solids Content
CHEM-SEAL 14-WB is a high performance, water based, acrylic sealer and dust proofer with 14% solids content by weight. It is a milky white emulsion, which dries to form a clear semi-gloss to high-gloss film. CHEM-SEAL 14-WB is UV stable and weather resistant. It is designed to protect all indoor and outdoor concrete and masonry surfaces on residential, commercial and light industrial applications.
CHEM-SEAL 14-WB can be used on concrete floors and walls, decorative concrete, stained concrete, stones, terrazo, and wood. Areas of applications include:
| Product | Packaging |
| CHEM-SEAL 14-WB | 1 GAL (3.785 LITER) JUG |
| 5 GAL (18.925 LITER) PAIL | |
| 55 GAL (208 LITER) DRUM |
| Property @ 25°C (77°F) | Value |
| Specific Gravity | 1.016 |
| Solid Content by Weight, % | 14 |
| Freezing Temperature, ºF (ºC) | ≈32 (0) |
| Color | Milky white, dries clear |
| Fumes | None |
| Flammability | None |
| Curing Time @ 77°F (25°C), minute | 20 minutes |
| Drying Time @ 77°F (25°C), hour | Touch dry = 2 |
| Firm Set = 24 | |
| Re-coat interval, hour | 2 to 4 |
| Finish | Smooth and gloss |
Methods of Application: By spraying, rolling or brushing.
Tools Needed: CHEM-SEAL 14-WB can be applied using one or more of the following:
Surface Preparation: The substrate must be sound, dry, clean and free from any contaminant like dust, dirt, mildew, algae, curing compounds, form release, sealers, oils, grease, etc.
Dirt and dust can be removed by sweeping and low-pressure washer. Areas contaminated with mildew, algae, oils and grease can be cleaned using a high-pressure washer and a biodegradable concrete cleaner like CHEM-CRETE CONCLEAN CCC060.
Cleaning of substrates treated with curing compounds, form release and sealers might be achieved by means of mechanical methods, such as shot blasting, grinding, wire brushing, and high-pressure washer.
Do not use acid etching, solvents or adhesive removers to clean substrates prior to application of CHEM-SEAL 14-WB.
Mixing: CHEM-SEAL 14-WB is ready to use; however, it is recommended to be stirred before use. Take the required quantity into the paint tray or the sprayer for application and tightly close the product’s container.
Coverage: 200 ft2/Gallon (4.91 m2/liter). Coverage depends on the porosity of the substrate and the final gloss required.
Compatibility: CHEM-SEAL 14-WB can be applied over virtually all sound substrates such as old masonry, old concrete, new masonry, new concrete, brick, terrazzo, unglazed tiles, asphalt, natural stone, etc.
CHEM-SEAL 14-WB can also be applied over materials that may degrade under UV rays to protect against such degradation. Example of these materials is polyurethane foams.
Limitations:
Cleaning: tools, equipment, spray unit, etc. can be cleaned immediately using water only.
Store the product in cool dry area. Recommended storage temperature is from 40°F to 95°F (+4.4°C to +35°C). Don’t expose container to direct sunlight. PROTECT FROM FREEZING. Keep container closed when not in use. Shelf life is minimum 1 year in its original unopened container.
As all chemical products, adequate care must be taken. Avoid direct contact with food, eyes, skin, and mouth. KEEP AWAY FROM CHILDREN AND ANIMALS.
Breathing mask, goggles, and gloves should be worn during the application of CHEM-SEAL 14-WB. Skin contamination should be cleaned with plenty of water. If splashed into the eyes, it should be washed with a plenty of water using an eye-cup Optrex or Isogutt solution, then consult your doctor
LIMITED WARRANTY: International Chem-Crete Inc. warrants that, at the time and place we make shipment, our materials will be of good quality and will conform to our published specifications in force on the date of acceptance of the order.
DISCLAIMER: The information contained herein is included for illustrative purposes only and, to the best of our knowledge is accurate and reliable. International Chem-Crete Inc. is not under any circumstances liable to connection with the use of information. As International Chem-Crete Inc. has no control over the use to which others may put its products, it is recommended that the products be tested to determine the suitability for specific applications and/or our information is valid in particular circumstances. Responsibility remains with the architect or engineer, contractor and owner of the design, application and proper installation of each product. Specifier and user shall determine the suitability of the product for specific application and assume all responsibility in connection therewith. AM300117.
